Easter Bunny Bags

Happy Easter!  I didn’t get a chance to have this posted until Easter because I didn’t finish putting the draw string on the bag until last night.

I’m looking for something different to do this year for Easter, so I did my usual and took to Pinterest for inspiration.  I was thinking of getting a big stuffed animal for each kid with a bag (instead of a basket) with the other goodies in it.  With the larger stuffed animal I wanted a smaller bag, but one big enough to hold some candy and other small goodies.

I came across this blog that has an adorable bunny bag!: http://judith-justjude.blogspot.ca/2016/03/bunny-bags-part-2-tutorial.html 

The instructions on the blog are really good, so I ended up “forgetting” to take a few of my normal pics.  I did make one change in how I did one part, so I will go into more detail during that part.

The first change I made was increase the size.  I outlined how big I wanted to cut each piece, and how many pieces.  I made four bags because kids ask questions if the Easter Bunny doesn’t bring THEM stuff too…and aren’t we all kids at heart anyway?  I didn’t have any fabric that screams “EASTER” and I wasn’t about to run out and get some, so I found fabric the kids would like.


After picking out the fabric, cut the pieces to size.  I made my ears in between making the bag part, I like to always have something on the sewing machine, for me it saves thread.  The quick overview is don’t sew the top two inches on both sides, but sew along the edges and bottom.  Then line up the two seams to “flatten” out the bottom, and draw a 2 inch line.  I used clips to keep the bottom in place and drew the line on both ends of each piece.


To take quick side trip to complete the ears!  I used pattern paper and traced (on my iPad screen) the ear.  This was frustrating because it’s a touch screen and kept changing…BUT I only drew half the ear, folded in half and cut it out.  Make sure your front fabric is faceing each other, then draw the ear shape on all ears.  Sew along the line, trim the extras, and turn inside out.  I used a chopstick to get the shape of the tip of the ear crips.  Then I ironed the tip of the ear while I made sure the end was flat along the seams.  I let the Iron sit on it for a few minutes, then I quickly pushed in the open end so I could. Easily sew along it.  Then sew along each end to finish the ears.


This is where it gets slightly different.  I still clip/pin the flaps together (forgot to take this pic).  Make sure to always only sew two pieces of fabric together at all times!  I started at the end of one flap, this would be the back flap that I would iron and sew it closed while I sew it against the bag.  Then the tricky part gets when you sew along the short side you will start to hit the edge of the bag that you’ve already sewn, so you need to flip fabric over to move onto the next flap.  (Top left) Once you get right up to the part already sewn, stop and leave the needle in and lift up th foot.  (Top right) Carefully flip over the top piece.  (Bottom left) as you can tell there is still one more piece, do the same and pull that piece over to the back.  (Bottom right) As you can tell you now only have two pieces.  You need to do that twice on each piece.  When you get to the end, make sure to leave a space to flip the bag right side out.


Turn the bag right side out, this can be challenging if you leave too small of a hole to flip right side out.  I tend to leave about a 2 inch hole and it worked great.


Then, use a chopstick to finish turning the flaps right side out, making the corners nice and crips!  After using the chopstick to get the corners turned out, use the iron to make the seam nice and crisp.


Find the side with the hole you used to flip the bag right side out.  Fold that piece inside to the seam and sew along the edge, that will attach the piece to the side and it will finish the open hole.  Make sure to pin this straight, if you don’t you may end up like me and not have a straight line sewn on the outside.  After you finish sewing the one side, flip it over and fold over the other end.  Then place two ears on top of the end, making sure the end of the ear lines up with the bottom of the piece folded over.  I used clips to keep the ears in place.  Sew along the bottom edge, just like you did with the other side.


Here is what mine look like at this step.  At this point it was almost time for the kids to get home, so I set it aside and finished the last part later.

Run two pieces of string through the top, I ran one string through one side, then two strings through the second side.  I tied the first string closed on the end and ran the second string through the last piece and tied it closed on the opposite side.  


They turned out SO Cute!  

Activity Bag for Kids

If you have kids, you know it can be a challenge to get them to sit for too long.  I used to stash some crayons and paper in my purse, but I just didn’t feel like the extra clutter anymore.  I also thought, as the kids got older, that different things would be fun to include.  This post will just be about making the bag, but you can fill them with just about anything!  One think I decided to stay away from are caryans because I didn’t want them to melt in the car, so I picked up some washable markers.  

I started with material, I picked up one fat quarter per bag, one zipper per bag, and a clip.  I thought 6×12 would be the ideal final size.  I also wanted the zipper to go along the long end, and I wanted to give zipper tabs a try!  Below is the final overview of what I used, each is per bag.

  • 6 1/2 x 12 1/2 inch piece for the back
  • 5 1/2 x 12 1/2 inch piece for the larger front piece
  • 1 1/2 x 12 1/2 inch piece for the top smaller front piece
  • 1 zipper that matches the fabric
  • 2 zipper tabs – They need to be at least 1/2 inch wider than the zipper and at least 5 or 6 inches long (or longer depending on how short your zipper is).  Mine ended up being 2 x 6 inches
  • 2 x 6 inch (you could make it 5 inches if needed), for the keychain strap
  • Keychain and clip.


Start by cutting your fabric for each bag.  Before cutting the zipper tabs check to see if they need to be longer than 6 inches (keep in mind it will be folded over, so I allotted about 2 1/2 inches per side).  


Zipper Tabs – The first thing I did was get the zipper ready, this started with making the zipper tabs.  Take your 2 x 6 inch pieces, two per bag and iron flat.  On one of the long ends iron about a 1/4 inch seam.  Take your zipper and slide it under the first seam and fold over the excess fabric to get the tab the same width of the zipper. Pull out the zipper before ironing, do not iron the zipper!  Iron a 1/4 inch seam on both short ends.  Last step is to fold in half and press all seams. The tabs are now easy to be seen onto the zippers. 


Time to sew the zipper tabs!  You need to avoid sewing on the metal, so keep that in mind when positioning the tabs on the zipper. When sewing the Bergen I get of the zipper, unzip slightly and use your fingers to keep the two pieces in place. 


Now that the zippers are completed, it’s time to sew the two front pieces onto the zipper.  Make sure to use your zipper foot, if you don’t have one expect to ruin a zipper or two if you aren’t perfect.  My machine came with one, once I figured out I had it – it has been a lifesaver!

Make sure the zipper is zipped all the way up, lay the zipper down with the zipper pull on the left side.  Take your small front piece and lay it on top of the zipper, look at the two ends to make sure the zipper is as even as you can.  Put it on the sewing machine with the zipper pull on the back of the machine and have the needle a little bit below the zipper pull.  My zipper had wide fabric attached, so I offset my fabric a little bit.  See the bottom images for the example.  Once you’ve sewn all the way down, the next step will be to un-zip the zipper and finish sewing the top part.

Flip the piece of fabric right side up and sew along the zipper, you should be able to go the entire length without hitting the zipper tab.  I always like to do this to give it a nice finished look and to also help secure the fabric.  I’ve also found if I don’t sew along the top like that, the zipper can get caught in the fabric from time to time.

Attach the bottom front piece similar just like you did the small top piece.  Make sure to also sew along the top.



After you finish the front piece it’s time to work on the key chain strap.  Fold the piece over and sew along the long end.  Turn the pieces inside out and iron flat.  I like to make sure the seam is in the middle when I iron.  Sew along the two edges to finish.

Now that all three main pieces are done it’s time to start laying them out.  Start with the front zipper piece.  I opened the zipper just slightly, then took the keychain piece (with keychain) and placed in the top right corner right next to the zipper pull.  I didn’t want the keychain piece to be too long so I lined it up with the base of the zipper.


After I put the keychain holder in place I used a clip to keep it in place.  Then lay the back of the bag facing down on top of the front piece.  After lining it up I clipped all four corners to get ready to sew.  


Sew along all four corners, you do NOT need to save a hole to turn it right side out becasue you have the zipper.  I always check to make sure I stitched correctly around all edges before I turn it over.  Trip off all extra fabric, then open up the zipper and turn right side out.


Turn the bag right side out and iron the edges.  Be very careful to not iron the zipper, if you do it might melt and not work.


Sew along the four edges to give it a nice finished look.  Attach the clip and your all done!


Here are a few more pictures of the finished prodcuts!  



Cloth Basket

I added shelves to my closet a month or two back and I’ve loved how it’s working out!  I just need more baskets, so I decided to finally try my hand at a cloth basket.  I also want to make a cloth basket for my trunk, the elastic net is just not working like it used to (it was for my previous car anyway so it’s OLD).  I wanted to give my closet baskets a try first so I can try them out and see if they would work for the trunk.  While I LOVE these baskets, and they work great for my closet…they just aren’t the basket for the trunk.  I will be making some slight adjustments to get stiff sides, I just need to design it. 

So, to get started, I used the basic basket idea from this blog post: http://haberdasheryfun.com/fabric/diy-reversible-fabric-storage-bin

I measured the size of the baskets I have and mapped out how to make these baskets.  I wanted the base to be 9 1/2 by 13, I also only wanted one piece of fabric folded in half (instead of sewing to pieces together, basically I didn’t want a seam on the bottom of the basket).

Figuring out the math wasn’t too difficult.  For the width I needed 13 + 9 1/2 + 2 seams, when folding it in half you will need to add 1/2 of each of the sides, plus two seams.  The second measurement will need the height of the basket plus 1/2 of the base and two seams, so 8 + 4 3/4 + 1/2 = 13 1/4.  I didn’t want the bottom seam so I doubled the number to get 26 1/2.  You will need to cut three pieces, an outside fabric, inside fabric, and Pellon 809 Bond.

Take the Pellon 809 bond and iron that onto one of the pieces of fabric, I chose the outside fabric.  Then fold in half and sew along the two edges.  After sewing I ironed the bottom edge flat so I would have a crisp line to line up the side seam with.  Then take one of the side seams and line it up against the inside iron line, do that with the other side and you will end up with a diamond.  Finally on each side draw a 9 1/2 inch line, I lined up the 10 inch mark on my ruler against the seam.  After drawing that line on both sides of each piece sew along the line.


Now that you have the base of the basked completed, take the inside fabric and turn it right side out.  Take the two pieces and tuck the inside piece inside the other, so the outside fabric is faceing eachother.  Take clips or pins and clip the pieces together, be sure to line up the seams first and add other clips around.  Sew around the edge leaving a gap, mine ended up larger than normal (about 6 inches?) due to the stiff fabric.  

After sewing, turn right side out.  The blog I used as a tutorial had you ironing the sides, I skipped that part.  I tried, but it just wasn’t working well.  I clipped the open fabric down so that is ready to be sewn around and closed up.


Sew along the outer edge to finish the basket!  That’s it!  It’s a pretty easy basket, and if you wanted to add handles you could easily do so without taking too much more time.  The baskets really did turn out great, I’m sure I will be making a few more for my closet.